MAYIN Guides

Katori Blouse Cutting and Stitching: Measurements, Draft and Fit Fixes

Four line drawings of drafting one half of a katori blouse front, from the basic front to the separated upper front, katori cup and band

Katori blouse cutting means splitting each half of the blouse front into separate pieces, usually an upper front, a cup shaped katori over the bust and a band underneath, so the bust gets a rounded, defined shape. You draft a front from your own measurements, mark the apex (bust point) and the under-bust line, draw the katori seam through the apex, then cut the pieces apart, add seam allowance and stitch the front pieces together before the shoulders, sides and sleeves. Below are approximate measurements in inches, a four step draft, a cutting layout for a 1 m blouse piece, the stitching order and the fit faults to catch at the trial. If you are still deciding between a katori and a princess cut, read our princess cut vs katori blouse guide first; this one is the how-to.

Shop the edit: our sarees with a blouse piece bring together sarees that come with fabric for the blouse, from pure handloom linen and mul modal to chiffon sarees with a 1 m crepe blouse piece.

Katori blouse cutting at a glance
3 partsOn each side of the front: upper front, katori cup and band
About 1 mOf fabric for a katori blouse with short or elbow sleeves
2 to 3 inA usual depth for the band under the bust
BiasKatori cups are usually cut diagonally across the weave

What a Katori Blouse Is

Katori is Hindi for a small bowl. In a katori blouse the bust is cut as separate, bowl shaped panels instead of being shaped by darts in one flat front. Each cup is joined to a piece above it and to a band below it, and the band holds the blouse close under the bust. The result is a rounder, more lifted shape than a plain darted blouse, with seams that you can see on the front.

Katori is a way of cutting the front, not a neckline. You can pair it with a round, U, square, sweetheart or boat neck and with any sleeve. For the names you will hear (single, double and half katori, katori belt blouse), padding, and how it compares with a princess cut, see the princess cut vs katori guide. Here we stay with the cutting table.

Katori or a plain darted front
KatoriDarted front
Front piecesUsually three per side, joined by seamsOne per side, shaped with darts
ShapeRounder and more defined over the bustSofter, flatter front
CuttingMore drafting; cups often cut on the biasQuicker; the usual first blouse
AlterationsLittle to let out in the cups; sides onlyEasier to let out at side seams
Best fabricsFirm or medium weight: cotton, linen, crepe, lined fabricsMost fabrics

Pieces, Tools and Fabric

Tailors divide the katori front in slightly different ways. The pieces below follow one common draft with front hooks and short sleeves. Most of them are cut twice, as a mirrored pair, because the fabric is folded.

Katori blouse pieces
PieceHow manyNotes
Upper front1 pairShoulder, neck and armhole down to the katori seam
Katori cup1 pair, or 2 pairsOver the bust, with a dart to the apex; often cut on the bias. Some drafts cut a second pair as a self lining
Band2 pairsUnder the bust, two layers for a firm hold
Back1 on the foldWith two waist darts; or 2 pieces for a back opening
Sleeves1 pairFrom a sleeve pattern that already fits you
Plackets2 stripsOne for hooks, one for the loops or eyes
Neck finish1 bias strip or a facingA bias strip is usual on cotton; a facing suits a deep or shaped neck
What you need on the table
Brown paper or pattern paper, a long ruler and a curved ruler (a French curve) for smooth seams
Tailor's chalk or a fabric marker, pins or pattern weights, and sharp fabric scissors
A measuring tape and your measurements written down in inches
Lining: soft cotton is the usual choice under cotton, linen and crepe
Hooks or a zip, matching thread, and a rolled towel to press the curved seams over

About 1 m of fabric usually covers a katori blouse with short or elbow sleeves. Full sleeves, a long blouse or a large print that needs matching across the cups will need more. Firm, smooth fabrics hold a cup best. Cotton, handloom linen and crepe are good first choices. Very soft or slippery cloth can still work, but line every piece and staystitch the curved edges. Our blouse fabric guide covers pre-washing and choosing blouse material.

Measurements for Katori Blouse Cutting

You need the same measurements as for any fitted blouse. Our blouse measurement and fitting guide explains how to take each one, so here we only list the ones a katori draft leans on and where each goes. Measure over the bra you will wear with the blouse, or over a light unpadded bra if the blouse will have sewn-in cups.

Line drawing of a blouse front showing shoulder to apex, apex to apex, full bust, underbust and front length measurements
The measurements that place the katori: shoulder to apex sets the height of the cup point, apex to apex its spacing, and the underbust sets the band.
Where each measurement goes in the draft
MeasurementRough checkUsed for
Shoulder to apex9 to 11 inHow far down the cup point sits; the height of the katori seam
Apex to apex7 to 8 inHalved, how far each apex sits from centre front
Full bustYour own figureThe width of the front at the bust line, plus ease, and the size of the cups
UnderbustYour own figureThe length of the band. It has to be exact
Waist or blouse hem roundYour own figureThe lower edge of the band, if the blouse ends below the underbust
Front length14 to 16 inShoulder to hem over the bust; the front is longer than the back
Shoulder, armhole, neck depthsYour own figuresThe upper front and the back
Why there is no size chart here
The rough check column only helps you spot a figure that looks wrong. It is not a size chart. People often search for a katori cutting chart for a 34 or 36 size, but two people with the same bust can have very different apex and underbust figures, and those two numbers decide whether the cups sit right. Draft from your own measurements.

Drafting the Katori Front Step by Step

The most reliable way to draft a katori front is to start from a front that fits and divide it. The shaping stays where your body needs it; only the seams move. Work on paper without seam allowance and add it at the very end. The drawing shows one half of the front, centre front on the left.

Four line drawings of drafting one half of a katori blouse front: the basic front, the apex and under-bust line marked, the katori seam and dart drawn, and the upper front, katori cup and band separated with seam allowance
Drafting one half of the front in four steps. One common division; your tailor may split it differently.
Drafting one half of the front
1
Draw a basic frontDraft a basic darted blouse front from your measurements, or trace the stitching lines of a darted blouse that already fits you, laid flat. Mark centre front, the neckline, the shoulder, the armhole, the side seam and the hem.
2
Fix the apexMeasure your shoulder to apex down from the point where shoulder meets neck, often 9 to 11 in, and half your apex to apex in from centre front, often 3.5 to 4 in. Where they meet is the apex. Draw a level bust line through it.
3
Draw the under-bust lineMark where the band will start, at your underbust, and draw it straight across from centre front to the side seam. The band is usually about 2 to 3 in deep, ending at the blouse hem.
4
Draw the katori seamWith a curved ruler, draw a smooth line from centre front, through the apex, to the bottom of the armhole. Above it is the upper front; below it, down to the band, is the katori.
5
Move the shaping into the katoriThe bust shaping of the darted front now goes into a dart from the under-bust line up towards the apex. Stop it about 1/2 to 1 in short of the apex so the point does not show as a peak.
6
Add notches and grain linesMark two notches on each seam, one each side of the apex, so the pieces line up when you join them. Draw a straight grain line on the upper front and band, and a line at 45 degrees on the katori if you will cut it on the bias.
7
Separate and add seam allowanceTrace each piece on to fresh paper and add seam allowance all round: more at the side seams, so the blouse can be let out later.

Published drafting methods put numbers to these steps. One textile training draft, worked for a 36 in bust and 30 in waist, gives the cup a width of about one sixth of the bust plus 1.5 in, so about 7.5 in, makes the band about 2.5 in deep and a quarter of the waist plus 1 in long, and leaves about 1.5 in at every side seam. Use figures like these as a check on your own draft, not as a replacement for it.

Seam allowance to add
EdgeAboutWhy
Neckline and centre front1/4 to 1/2 inFinished with binding, a facing or a placket
Katori seam and band seam1/2 inEnough to clip the curves without fraying
Shoulder and armhole1/2 inThe sleeve is set in here
Side seams1 to 1.5 inRoom to let the blouse out later
Hem of the band1/2 inTurned in when the two band layers are joined

Single or Double Katori: Shaping the Cup

Many tailors call a cup cut as one section a single katori, and a cup split into two sections a double katori. Others use the words differently, so show a picture before you agree on a name.

Single katori blouse with one cup section and a dart, beside a double katori with each cup split into two sections
One cup section or two. Both are drafted from the same apex and under-bust line.
How each cup is drafted
Single katoriThe katori stays one piece. The dart from the under-bust line takes in the shaping. Simple to cut and the easiest first katori.
Double katoriThe katori is split by a second seam through the apex, so each cup has two sections. Turn the dart into that seam. It gives a rounder, more shaped cup, but adds two more seams to match.
Gathers instead of a dartSome tailors gather the lower edge of the katori into the band instead of sewing a dart. It is softer and forgiving on thin fabric, but less defined.

Whichever you choose, the cup point must land on your apex. A cup that is too deep leaves a hollow; one that is too shallow flattens the bust and pulls the band up at the front.

The Back, Sleeves and Band

The back of a katori blouse is a plain blouse back. Cut it on the fold with two waist darts, or as two pieces if the blouse opens at the back. One published draft uses back darts about 3.5 in long and 3/4 in wide. Draft the back neck to the shape you want; our blouse back neck designs guide gives depths in inches.

The back shoulder must match the front shoulder in length, and the front and back armholes must meet smoothly at the side seam. Walk the seam lines against each other on paper before you cut.

Sleeves come from a sleeve pattern that already fits you. Set the sleeve notches at the front and back armholes as usual. For sleeve lengths and shapes, see our saree blouse sleeve designs; for a softer look over a katori, the batch guide to frill blouse designs shows ruffled and tiered sleeves.

Getting the band right
LengthYour underbust, plus the overlap for hooks at centre front, plus side seam allowance.
DepthUsually about 2 to 3 in finished. Deeper bands hold better on heavier fabric.
Two layersCut the band twice and join the layers. Interfacing one layer helps on soft fabric.
Straight grainCut the band on the straight grain so it does not stretch round the body.

Cutting the Fabric and Lining

Pre-wash and press washable fabric before you cut, so it does not shrink after stitching. Fold the fabric in half lengthwise, right sides together, with the selvedges level. Cutting through two layers gives you a mirrored pair of every front piece in one go.

Cutting layout for a katori blouse on a folded 1 m blouse piece: back on the fold, sleeves, upper front, two pairs of band pieces, katori cups on the bias and a neck bias strip
One way to lay out the pieces on a folded 1 m blouse piece. Check the fit of every piece before you cut.
Cutting in order
1
Lay out every piece firstPlace all the pattern pieces before you cut anything. Back on the fold, the upper fronts and band on the straight grain, the katori cups at 45 degrees.
2
Check the print and the borderOn a print, place the katori pair so the motifs match across centre front. If the blouse piece has a border, decide now whether it goes on the sleeves or the band.
3
Chalk, then cutDraw round each piece with chalk, mark every notch and dart, then cut on the line with long, steady strokes.
4
Mark the apexMark the apex and the dart point on the wrong side of each katori with chalk or a pin.
5
Cut the liningCut the lining from the same pieces. Cutting the katori lining on the straight grain, even when the outer cup is on the bias, helps stop the cup stretching.
6
Staystitch the curvesStaystitch the katori seam, the neckline and the armholes just inside the seam line, within the seam allowance, so the bias edges do not stretch while you work.

For lining fabrics and how to cut them, see our blouse lining guide. If your saree has a running blouse piece woven on to one end, cut it off along the line where the saree ends before you lay out the blouse.

Katori Blouse Stitching Order

A katori blouse goes together front first. Join the small front pieces into two finished halves before the shoulders and sides, and fit before the sleeves go in. Tack (baste) by hand or with a long machine stitch for the trial, and sew the final seams after it.

Stitching in order
1
DartsSew the katori darts from the wide end to the point, and leave long thread ends to tie off rather than backstitching at the point. Sew the back darts.
2
Katori to upper frontPin each katori to its upper front at the notches, easing the curve, and sew the katori seam. Clip the seam allowance on the curve and press it over a rolled towel.
3
BandJoin the two layers of each band along the top edge to the katori, outer layer to the outer fabric, then fold the inner layer up and sew or slip stitch it in place.
4
PlacketsAttach the plackets along centre front, stitching on the right side, turning in and stitching again. One side carries the hooks, the other the loops or eyes.
5
Shoulders and sidesJoin the front to the back at the shoulders, then down the side seams. Stitch the sides at your marked line, leaving the extra allowance inside.
6
Trial fittingTry the blouse on with the bra you measured over. Check the cup points and the band, then adjust before the final stitching.
7
SleevesSet the sleeves into the armholes, matching the notches and the side seam.
8
Neck, hem and hooksFinish the neck with a bias strip or a facing, close the hem, sew on the hooks, and press the whole blouse.
Lining tip
On a lined blouse, many tailors join each outer piece to its lining piece first and then treat the two as one layer through the rest of the order. It is quicker and keeps the katori seams neat inside.

Fit Fixes for a Katori Blouse

Ask for a trial before final stitching, or give yourself one at home. A katori is easiest to correct while the seams are only tacked, because small bias pieces leave little to let out once they are sewn and trimmed.

Trial fitting checks for a princess cut blouse and a katori: seam over the apex, and a level katori band beside one that tilts up
At the trial: the cup point on your apex and the band level all the way round.
Katori faults and fixes
You noticeUsually meansFix
Cup points above or below the bustShoulder to apex measured or drafted wronglyMove the katori seam and dart point to your marked apex
Cups too far apart or too closeApex to apex offMove the dart and seam towards or away from centre front
A hollow or loose cupThe cup is drafted too deepTake in the dart or the cup seam
Pulls across the bustThe cup is too shallow, or too little easeLet out the dart, or add width at the side front
Band rides up at the frontFront too short to go over the bustAdd length to the katori, not a bigger size
Wrinkles where cup meets bandUneven easing, or a band cut too tightUnpick and re-ease the join; check the band length
Upper front gapes at the neckNeck too wide or deep for the cutTake in at the shoulder seam, or add a facing that holds the edge
Cup edges stretch and rippleBias edges not staystitchedStaystitch, or back the cup with lining on the straight grain
Final checks before you stitch
The point of each cup sits on your bust point, neither above nor below it.
The band runs level all the way round and does not tilt up at the front.
No wrinkles or hollows where the katori joins the band.
Raise your arms, sit and lean forward: the band stays put and nothing gapes.
Run a finger under the band: snug, not tight.

For extra hold with a fuller bust, see our guide to blouse designs for a heavy bust. For which neckline to put on top of the katori, see saree blouse neck designs.

Sarees With a Blouse Piece for a Katori

A katori needs a firm enough fabric to keep its cup shape. These MAYIN sarees come with a blouse piece that works well. Every MAYIN saree is 5.5 m long and 45 inches wide. Our linen sarees come with a 1 m blouse piece; handloom linen holds a crisp cup and suits a structured katori, and they are dry clean only at ₹3,999. Our chiffon sarees come with a 1 m crepe blouse piece, and crepe has the body a katori needs. They are dry clean. Mul modal sarees come with a 1 m running blouse piece in the same fabric. It is soft and fine, so line it and choose a single katori with a firm band. Plain mul modal takes a gentle cold hand wash.

Main Event, Composure and On Repeat are pure handloom linen with a zari border, ₹3,999 each, with a 1 m blouse piece, dry clean. Solenne (₹3,399) and Orelia (₹3,999) are pure chiffon, and Damask Rose (₹3,499) is a hand painted chiffon; all three come with a 1 m crepe blouse piece and are dry clean. True Garnet and Mauve Melody are plain mul modal at ₹1,899, with a 1 m running blouse piece and a gentle cold hand wash. Delivery is free in India on orders of ₹2,000 and above.

Questions People Ask

What is a katori blouse?

A blouse whose front is cut in separate pieces, with a bowl shaped cup over each bust joined to a band underneath. Katori means a small bowl in Hindi.

How many pieces are there in a katori blouse?

A common draft has three front pieces on each side (upper front, katori and band), with the band cut in two layers, plus a back, two sleeves, plackets and a neck bias strip. Some tailors split the cup again for a double katori.

What is the difference between single katori and double katori?

Many tailors use single katori for a cup cut as one section with a dart, and double katori for a cup split into two sections by a seam through the apex. The names vary, so show your tailor a picture.

How much cloth is needed for a katori blouse?

About 1 m usually covers a katori blouse with short or elbow sleeves. Full sleeves, a long blouse or matching a large print need more.

Is the katori cut on the bias?

Often, yes. Cutting the cups diagonally across the weave helps them curve over the bust. Staystitch the edges, and cut the lining on the straight grain to stop the cup stretching.

Which measurements are most important for katori blouse cutting?

Shoulder to apex, apex to apex and the underbust. The first two place the cup points and the third sets the band, which has to be exact.

Is there a katori blouse cutting chart for 34 or 36 size?

Paper patterns are sold by size, but the cups only sit right if they match your own apex and underbust figures. Use a size pattern as a starting point and check it against your measurements.

Which fabric is best for a katori blouse?

Firm or medium weight fabric that holds a curve, such as cotton, linen or crepe. Soft fabric works if every piece is lined.

Can a katori blouse be padded?

Some tailors pad a katori and others let the cups do the shaping on their own. If you want cups, ask your tailor how they handle them before cutting.

Can a katori blouse be altered later?

It can usually be taken in or let out a little at the side seams, within the seam allowance. The small bias cut cups leave little to change, so fit at the trial stage.

Why does my katori blouse band ride up?

Usually the front is too short to go over the bust, or the cups are too shallow. Add length to the katori rather than making the whole blouse bigger.

Do I need a lining for a katori blouse?

It is not essential on firm cotton or linen, but a lining helps the cups keep their shape, hides the seams and makes the blouse more comfortable. On soft fabric, line it.

All guides