MAYIN Guides

Saree Fall and Pico: What They Are, Which Sarees Need Them and Cost

Composure, a pink pure handloom linen saree with a zari border by MAYIN

A saree fall is a strip of plain cloth, usually cotton, stitched to the inside of the lower edge of a saree so the hem hangs straight and wears less. Pico is a narrow, tightly rolled edge, about 2 mm wide, run by machine along the cut ends of a saree so they do not fray. Most tailors in India offer the two together as "fall and pico", and many people have it done on a new saree before its first wear. Not every saree needs both, though, and some need neither. Below: what each one is, which sarees benefit, how it is done, what it costs as of 2026, and how to stitch a fall yourself.

Fall and pico at a glance
2 to 2.5 mUsual length of a ready fall strip
4 to 5 inUsual width of the fall
About 2 mmWidth of a plain pico edge
₹100 to ₹150Roughly, machine fall and pico at a local tailor, as of 2026
In this guide

What Is a Saree Fall

The fall is a long, narrow band of fabric sewn on the wrong side of the saree, along the bottom edge. It sits just above the hem, so it never shows from the outside, and it covers the part of the saree that wraps round your legs and forms the pleats. It does not go on the pallu, which falls from your shoulder and is seen on both sides.

Ready falls are sold in small packs at tailoring and haberdashery shops. Trade listings show them cut to about 2 to 2.5 m long and 4 to 5 inches wide, in cotton, poplin, poly cotton or polyester, in dozens of colours. Tailors usually start it at or near the plain end of the saree (the end you tuck in first), so it runs under the first wrap and the pleats. Some leave a short gap at that end; practice varies. On a typical six yard saree of about 5.5 m, the rest of the lower edge, up to and including the pallu, is left without a fall.

The parts of a fall job
The stripA cotton or satin band, about 4 to 5 inches wide, usually 2.25 to 2.5 m long.
Where it goesInside the lower edge, from near the plain end, covering the wrap and the pleats.
How highSet a little above the hem, from a few millimetres to about 2 cm, so it never peeps below.
The stitchTwo lines along the long edges of the strip, catching as little of the saree as possible so the stitches do not show on the outside.

Think of the fall as a lining for the hem. It does not make your pleats for you and it will not fix a drape that is tucked too loosely. What it does is give the bottom of the saree a little weight and a clean, protected edge. For how the pleats themselves are made, see how to make saree pleats.

What Is Pico on a Saree

Pico (also written picot, and in some cities called piko or edging) is the finish on the raw edges of a saree. A woven saree has two kinds of edge. The long edges are selvedges: the weft turns back at the edge of the loom, so they cannot fray. The two short ends, where the saree was cut from the loom or from a longer length, are raw. So is the end left behind when an attached blouse piece is cut off. Pico rolls these raw ends into a very narrow hem and binds them with dense thread so they stay sealed. To find where the blouse piece ends before you cut, see our saree length and size guide.

On a printed or sheer fabric that was cut from a wider roll, such as chiffon or georgette, the long edges can be raw too. Those sarees often get pico along every edge, which is why you sometimes see a thin coloured line of thread running round a chiffon saree.

Fall and pico side by side
FallPico
What it isA strip of cloth stitched inside the hemA narrow rolled and over-stitched edge
WhereLower edge, wrap and pleats onlyCut ends, and raw long edges on cut fabrics
What it doesWeight, a straight hem, protection from wearStops fraying and loose threads
Done byHand or machineA pico (rolled hem) machine
Seen from outsideShould not beYes, as a fine line of thread

Pico comes in more than one style. Plain thread pico matches the saree colour and almost disappears. Decorative pico uses contrast thread, a tighter scalloped stitch, or tiny beads (moti pico) along the edge, and is chosen as a trim. If you want the ends to look plain, ask for matching thread.

Why Sarees Get a Fall and Pico

The bottom edge of a saree takes the most wear. It brushes the floor, rubs against your sandals and gets caught under chair legs. Without a fall, that friction slowly thins the threads at the hem. With a fall, the strip takes the rubbing and can be replaced when it wears out, while the saree stays intact.

What each one does for you
A straighter hemA little extra weight at the bottom helps the pleats hang in a clean line and stops a light hem from flipping or curling.
Less wearThe fall protects the hem from floors, footwear and repeated tucking.
A neater insideOn a printed saree, the fall also covers the faded wrong side of the hem where the pleats open as you walk.
No frayingPico seals cut ends, so washing and wearing do not unravel them.

Both are usually done before the first wear, because an unfinished cut end can lose threads the first time it is washed or caught. A saree with a hand-knotted fringe or tassels at the pallu end is different: the fringe is the finish there, so that end is not picoed. Our saree tassels guide covers those ends.

Which Sarees Need a Fall, Pico or Both

It depends on the fabric, the weight and how you wear the saree. Tailors often add fall and pico to every saree by habit, but a few sarees drape better without a fall, and a selvedge never needs pico. Use this as a starting point, then trial-drape once before you decide.

By saree type
SareeFallPico
Heavy woven silk with a thick zari borderUsually yes, a firm cotton fall to take the wearOn the cut ends, avoiding zari
Soft silk, crepe, georgetteTrial-drape first; a light satin fall if the hem curlsYes on cut ends; often on all edges of georgette
ChiffonOpinions differ; trial-drape first, and if you add one, keep it very light and close in colourUsually on all raw edges
Cotton and mul cottonHelpful for daily wear; a light cotton fallCut ends only, if they are raw
LinenHelpful; a narrow, light fallCut ends only, if they are raw
Tissue, organza, sheer weavesOnly a light, matching fall, or none, as an opaque strip shows throughCut ends, with fine thread
Fringed, scalloped or cutwork edgesAsk about a narrow binding insteadNot on a fringed end
Pre-stitched or ready to wear sareesUsually already finishedUsually already finished

For tissue and other sheer weaves, see what is a tissue saree. Two quick tests help. Hold the lower edge up to a window: if you can see your hand through it, any fall will show, so keep it very light and close in colour, or skip it. Then drape the saree once without a fall and walk around. If the hem sits straight and the pleats hang well, you may not need one. If the hem flips up, twists or the pleats spread at the bottom, a fall will help.

Light sarees
A light fabric such as chiffon or georgette often hangs well because it is fluid, and a stiff cotton fall can make the hem stick out. Some tailors add a light satin fall in the saree colour to stop the hem catching on heels; others leave it off. A trial drape settles it. Read more in what is a chiffon saree and our georgette saree guide.

How a Tailor Does Fall and Pico

A local tailor usually does both in one sitting. The pico takes about ten minutes on the machine; the fall takes longer because it has to be laid out straight over more than two metres.

What happens at the tailor
1
Opening the sareeThe saree is spread flat to find the plain end, the pallu end and the wrong side.
2
Picoing the cut endsThe raw ends, and any raw long edges, go through a pico machine, which rolls a hem of about 2 mm and binds it with thread.
3
Choosing the fallThe tailor matches a fall strip to the colour near the hem, usually the border or the body.
4
Placing the fallThe strip is laid inside the lower edge, starting near the plain end, set slightly above the hem.
5
StitchingBoth long edges of the strip are stitched down. On a careful job, the stitch catches only a thread or two of the saree, so it hardly shows outside.
6
CheckingThe saree is held up by the pallu to see that the hem lies flat, with no puckering and no fall peeping below the edge.

Machine stitching is quick and cheap, but the line of stitches can show on the right side of a light or plain saree. Hand stitching (a hemming or slip stitch) takes longer and costs more, but it is nearly invisible and kinder to fine fabric. For a plain mul cotton or a sheer weave, ask for the fall to be hand stitched if your tailor offers it.

Choosing the Fall: Colour, Fabric and Width

Most problems with a fall come from picking the wrong strip. A shiny or dark fall behind a light hem will show, and a heavy fall on a light fabric will pull the hem out of shape.

Match the fall to
ColourWhatever disappears behind the hemBorder or body colourSlightly darker rather than lighter
FabricCotton for cotton and linenSatin for chiffon and georgetteFirm cotton for heavy silk
WidthAbout 4 in for light sarees4 to 5 in for mostNarrower under a wide border

Colour: tailors differ here. Many match the fall to the border, because that is what it lies behind; others match the body colour, so the fall does not show when the pleats open. Hold both options against the inside of the hem, on the right side too if the saree is light or sheer, and pick the one you cannot see. A bright white fall under a cream or pastel saree is a common mistake. When you cannot find an exact match, a shade slightly darker usually hides better than one lighter.

Fabric and weight: the fall should never be heavier than the saree can carry. A firm cotton suits heavy silk. A softer, thinner cotton suits everyday cotton and linen. A light satin suits chiffon and georgette, though polyester satin can look shiny and feel warm, so check it against the fabric first. If you are going to stitch a cotton fall yourself, washing the strip once before you sew it is a sensible precaution against shrinkage.

Fall and Pico Cost in 2026

Fall and pico is one of the cheapest jobs a tailor does, but prices vary by city, by how busy the tailor is and by how the work is done. These bands are approximate, as of 2026, from tailoring price guides, online add-on prices and trade listings.

What it usually costs, as of 2026
JobRoughlyNotes
Pico only, by machine₹40 to ₹70Both cut ends; more if all edges are picoed
Fall and pico, by machine₹100 to ₹150Most common job at a local tailor
Fall and pico added when buying online₹120 to ₹200Usually adds 3 to 4 days to delivery
Fall and pico, hand stitchedRoughly ₹300Nearly invisible stitches
Heavy or embellished saree, hand finished₹350 to ₹400More care around zari and work
The fall strip aloneVery littleTrade listings show about ₹7 to ₹18 a strip, sold by the dozen; shops charge a little more

Most tailors return the saree in two to four days. In the weeks before big festivals such as Diwali, queues are long and it can take a week or more, so finish a festive saree as soon as you buy it. For what sarees themselves cost by fabric, see our saree price guide.

Before you send it
Shops that offer fall and pico as an add-on usually say that a saree cannot be returned or exchanged once it has been done, because the stitching changes the saree. Try the saree on and be sure you are keeping it before you send it for finishing.

How to Attach a Saree Fall at Home

A fall is a manageable home job if you can do a simple hemming stitch. It needs patience more than skill. Pico is much harder at home: it needs a rolled-hem foot or an overlocker, and a 2 mm hem on slippery fabric is fiddly, so leave pico to a tailor unless you already sew on such a machine.

What you need
A ready fall strip, about 2.25 to 2.5 m, in the colour of the hem.
Thread matched to the saree, not to the fall, and a fine hand needle.
Fine pins or clips, and an iron.
A long, clean surface: a dining table or a bed works.
A measuring tape, if you want to check the strip against the saree.
Stitching a fall by hand
1
Find the plain endSpread the saree wrong side up. The plain end is the one you tuck in first, opposite the pallu.
2
Press both piecesIron the lower edge of the saree flat. Fold and press about a quarter inch under along both long edges of the fall strip if they are raw.
3
Position the stripLay the fall along the inside of the lower edge, starting at or a little in from the plain end, with its bottom edge a few millimetres to about 1 cm above the hem.
4
Pin without stretchingPin every few inches along the full length. Keep both layers relaxed; stretching either one causes puckers.
5
Stitch the lower edgeUse a small slip stitch or hemming stitch. Take a deep bite in the fall and only a thread or two of the saree, so the stitch hardly shows outside.
6
Stitch the upper edgeRepeat along the top edge of the strip, keeping it flat against the saree.
7
Finish the endsTurn the short ends of the strip under and stitch them down neatly.
8
Check and drapeHold the saree up by the pallu and look at both sides. Then drape it once, pleats and all, before you call it done.

Taking the fall off later is easy: snip the stitches and lift the strip away. That is useful when an old fall has worn through, or when you want to pass on a saree without it.

Mistakes to Avoid and What to Ask Your Tailor

Fall and pico are simple jobs, but a careless finish can mark a saree for good. These are the problems tailoring guides warn about most.

Common mistakes
Stitches through to the frontMachine lines showing on the right side of a plain or light saree. Ask for a fine stitch or hand stitching.
Cutting the ends to straighten themTrimming the pallu end loses woven pattern or fringe. Ask for pico on the end as it is.
Pico over zariThe needle can snag metallic thread. Ask for the pico to stop short of a zari edge.
The wrong colourA fall that does not disappear behind the hem shows when the pleats open, or through a light fabric.
Too heavy a fallA stiff fall on a light saree makes the hem stand out from the ankles.
Say this at the tailor
Which end is the pallu, so the fall goes at the other end.
Pico on the cut ends only (or all edges, for chiffon and georgette), in matching thread.
No cutting of the ends.
Keep the fall a little above the hem, and catch only a thread of the saree.
Show me the fall colour against the hem before you stitch.
When will it be ready, and can I check it before I pay.

Care after finishing is the same as for the saree itself. Do not wring the hem when you wash a cotton or linen saree, as twisting strains the stitches, and iron the fall from the wrong side. For full care steps by fabric, see how to wash cotton, chiffon and linen sarees.

Sarees in This Guide

These MAYIN sarees cover the fabrics this guide talks about: light mul cotton and mul modal for daily wear, handloom linen, chiffon, tissue and jamdani. Every MAYIN saree is 5.5 m long and 45 inches wide. The chiffon sarees come with a 1 m crepe blouse piece, the mul modal with a 1 m running blouse piece in the same fabric and the linen with a 1 m blouse piece; mul cotton comes without one. Plain mul cotton and mul modal take a gentle cold hand wash, while linen, chiffon, tissue and jamdani are dry clean. For more on mul cotton, read what is a mul cotton saree, or browse all linen sarees and chiffon sarees.

Sarees in this guide

Questions People Ask

What is fall and pico in a saree?

A fall is a strip of cloth stitched inside the lower edge of the saree to give the hem weight and protect it from wear. Pico is a narrow machine-rolled edge on the cut ends that stops them fraying.

What is the difference between fall and pico?

The fall is an extra piece of cloth sewn inside the hem; pico is a stitched finish on the raw edges. A saree can have one without the other.

Is a fall necessary for a saree?

No. It helps a hem hang straight and wear less, especially on cotton, linen and heavier silk, but many light sarees drape well without one. Try the saree once without a fall before deciding.

Does a chiffon saree need fall and pico?

Chiffon usually needs pico, often on all its edges, because cut chiffon frays. A fall is optional and tailors differ; if you want one, choose a very light fall in a close colour.

Does a cotton saree need fall and pico?

A cotton saree with woven selvedges only needs pico on raw cut ends. A light cotton fall is useful if you wear the saree often, as it protects the hem.

How much does fall and pico cost?

As of 2026, roughly ₹100 to ₹150 by machine at a local tailor, ₹120 to ₹200 as an online add-on, and about ₹300 or more for hand stitching. Prices vary by city.

How long does fall and pico take?

Usually two to four days at a tailor. Before big festivals it can take a week or more.

How long is a saree fall?

Ready fall strips are usually 2.25 to 2.5 m long and 4 to 5 inches wide. That covers the wrap and the pleats on a six yard saree.

On which side is the saree fall attached?

On the inside of the lower edge, at the plain end of the saree, opposite the pallu. It sits a little above the hem so it does not show.

What colour should the saree fall be?

Match it to the border or the body colour, whichever disappears when you hold it behind the hem. If you cannot match it exactly, a shade darker usually hides better than a lighter one.

Can I put a fall on a saree at home?

Yes, with a ready fall strip, matching thread and a small hand hemming stitch. Pico is harder at home without a rolled-hem machine.

Can I return a saree after fall and pico?

Usually not. Most shops that offer fall and pico say a finished saree cannot be returned or exchanged, so be sure before you send it.

All guides